Mod Description
If DRLs are not standard on your car, you can buy an add on module by MisterDotCom (MDC) that adds the functionality to your car.Mod Details
PremiumNo Difficulty
Mod ID225
CreditSteven M
For
Linkhttps://dev.evilution.co.uk/mod/daytime-running-lights-mdc.htm Copy to Clipboard
Many thanks to Steven for allowing us to publish this modification. Steven is the distributer for MDC parts in Canada. If you are outside Canada and USA, visit the official MisterDotCom website.
Fitting DRLs
This kit comes with only one item – the DRL module.
Tools Required
10mm Socket Wrench, crescent wrench, or nut driver. mATC fuse puller, or small needle nose pliers. Flashlight (optional)
*NOTE* It is RECOMMENDED for safety reasons that you follow instructions provided in your car’s manual and disconnect the battery before installing or removing this device.
Preparation And Precautions
Before starting, make sure you have your car’s stereo security code if you will be disconnecting the battery. The dealer where you bought the car should be able to provide this for you if you don’t have it. Physical and electrical damage is not covered by warranty! Be certain to follow all instructions to avoid damage. In particular, the black fuse holders on the circuit board are especially susceptible to damage so take extra care when handling.
Access The Use Box
The fuse box is located above the driver foot well (above and to the left of the pedals). Simply pull down the black felt cover with your hands. All fuses are labeled by numbers moulded in the plastic. You may need a flashlight to identify them.
Making The Connections
Remove the three fuses at numbers 22, 23 and 24 from the fuse box and insert them into the three fuse holders on the DRL board. Be careful not to put any upward force when inserting the fuses as the holders are very susceptible to bending and breaking.
Now insert the Daytime Running Lights Mod into the newly vacated slots for fuse 22, 23, and 24 being careful to orient the device as shown in the photo below.
Next connect the orange fuse holder at the end of the yellow (red in photo) wire to one of the first 5 slots available on the side-rail of the fuse box. It doesn’t matter which one, as long as it is one of the 5 closest to the front of the car. The orange fuse holder will only go in one way and requires little to no force.
Finally, take the brown (black in photo) wire with the metal loop connector at the end over to the grounding bolt, which is located in front of (toward the front of the car) and to the left of the fuse box. There will be one or more other brown wires already connected to that bolt. Remove the nut with your 10mm wrench, connect the wire, and replace the nut.
Programming The DRL Board
Reconnect the battery if applicable. Turn the key to position ‘1’ (power on, engine off).
Daytime Running Lights (DRL) On/Off:
With your headlights off, flash the high beams (pull the headlight stalk toward you) 6 times in succession to toggle your DRL on or off. After the 6th flash, the system will indicate success by flashing the low-beams either once (indicates DRL is off) or twice (indicates DRL is on). Repeat to toggle again.
Coming Home Feature (CHF) on/off:
Turn the parking lights on (rotate headlight switch up to first click). From there, turn the headlights on (rotate up to second click) and off (rotate back down to first click) four times in succession (that is: on, off, on, off, on, off, on, off) to toggle . The system will confirm as before by flashing the low-beams either once (indicates CHF is off) or twice (CHF is on). Repeat to toggle again.
Set CHF duration:
The procedure is nearly the same as above, but with one important difference. After the fourth ‘on’ you pause before continuing with the 4th ‘off’ (That is: on, off, on, off, on, off, on… PAUSE… off). The duration of your pause (min: 5 seconds, max 5 minutes) will be remembered and set as the duration of your CHF. After you complete this step, the system will confirm with 3 flashes of your low-beam.
Turn your car off and remove your key to finish programming.
Finishing up
If your smart has factory DRL (all Canadian smarts) you must disable it to enjoy the benefits of this mod. To turn them off, see here for info.
A Canadian Quirk
All Canadian smarts already have Daytime Running Lights and the Coming Home feature (other smarts may have it as well). Disabling the factory DRL lets you take advantage of the bulb-saving features offered by this mod, but you can not (as far as I know) disable the CHF. With the factory CHF and this mod’s CHF both working, you get an odd compounded effect. The factory CHF will turn the lights on for a pre-set period of time then they will shut off, after a brief pause the mod’s CHF will engage and keep the lights on for the duration you programmed, then they will nicely fade off. Its an unexpected behavior and a bit odd, but causes no forseeable harm. To avoid this, simply program the mod’s CHF to ‘off’ as described above. (again, you can not turn the factory CHF off).